SDR
Revision as of 21:54, 4 June 2015 by <bdi>PhilippeTeuwen</bdi> (talk | contribs) (→Reverse engineering)
Hardware
HackRF
- 1MHz - 6GHz, RX/TX half-duplex, BW 20MHz, ADC/DAC 8bit
- https://github.com/mossmann/hackrf/wiki
- Bias-T supply can deliver 3.3V 50mA
- BW & filtering: https://github.com/mossmann/hackrf/wiki/Tips-and-Tricks
- FW flashing
$ hackrf_info Found HackRF board. Board ID Number: 2 (HackRF One) Firmware Version: 2014.08.1 Part ID Number: 0xa000cb3c 0x0067434c Serial Number: 0x00000000 0x00000000 0x15d463dc 0x383f8125
Airspy
- 24MHz - 1.750GHz, RX, BW 10MHz (9MHz alias free), ADC 12bit (10.4 ENOB)
- Bias-T supply can deliver 4.5V
- FW flashing
$ airspy_info Found AirSpy board 1 Board ID Number: 0 (AIRSPY) Firmware Version: AirSpy NOS v1.0.0-rc5-0-g648c14f 2015-05-20 Part ID Number: 0x6906002B 0x00000030 Serial Number: 0x618C63C82F7424A7 Supported sample rates: 10.000000 MSPS 2.500000 MSPS Close board 1
RTL-SDR
- ~25MHz - 2GHz, RX, BW 2.4-2.8MHz, ADC 8bit
- Mine: 52-2212 MHz with gap @ 1107-1241 MHz
LNA: Low Noise Amplifiers
- LNA4ALL
- 28-2500MHz, gain about 22dB from 28MHz to 600MHz then gain drops to ~16dB @ 1400MHz and ~11dB @ 2500MHz, 0.75dB NF @ 1 GHz and 0.98dB NF @ 2 GHz
- 6-9 V, 55-65 mA (5V if regulator bridged)
- can be powered by HackRF or Airspy if modified, 10uH SMD on OUT and regulator bridged (because we deliver <5V) or bridged by 100mA fuse, just in case.
- LNA4HF
- 150kHz - 30MHz, gain 18-20 dB, NF 1-2 dB
- 6-9 V, 18 mA (5V if regulator bridged)
- up to 2GHz if low-pass filter removed
- Better to position LNA near antenna than near receiver, more useful info here
Antennas
ANT500
- 50 ohms, 75 MHz - 1 GHz, 20cm - 88cm
Software
- https://github.com/mossmann/hackrf/wiki/Operating-System-Tips -> PyBOMBS
- HackRF specific: https://github.com/mossmann/hackrf/wiki/Software-with-HackRF-Support
Reverse engineering
Info
Generic
GQRX
Baudline
With hackrf:
Add offset to avoid DC, e.g. to monitor 440MHz -> 442MHz
E.g. somewhere around 100MHz @ 8MHz:
hackrf_transfer -r /dev/stdout -f 100000000 -s 8000000 | \ baudline -stdin -quadrature -channels 2 -flipcomplex -format u8 -samplerate 8000000 -memory 256
With airspy:
Freq is given in MHz, sample rate is given by fw offset: -a 0 = 10M, -a 1 = 2.5M
By default airspy_rx & baudline work with 16bit LSB samples
airspy_rx -r /dev/stdout -f 100 -a 0 | \ baudline -stdin -quadrature -channels 2 -flipcomplex -samplerate 10000000 -memory 256
Tuning:
- input / color aperture
- zoom: alt+arrows
- Hz zoom: require larger FFT (process / transform size)
27MHz RC
87MHz to 108MHz FM band
315MHz car keyfob
480MHz interferences
Stripes around 480MHz are because of poorly shielded USB cable
524 to 542 MHz wireless microphones
- http://www.sharebrained.com/2013/06/15/wireless-microphones-and-hackrf/
- microphone_shure.grc FM demodulator