Server Dell PowerEdge T410

Manuals

• here, online version of the main manual here with chapter on LED status here

Install notes

Basis

• In BIOS
  • Activate Virtualization support
  • Power Management -> OS Control
  • Report kbd errors: NO
• Installing squeeze (frozen but still testing) from daily image (17/08/2010)
  • Complains about missing bnx2/bnx2-mips-09-5.0.0.j3.fw & bnx2/bnx2-rv2p-09-5.0.0.j3.fw
    • Get it on another machine and put it on USB stick: aptitude install firmware-bnx2 ; cp /lib/firmware/bnx2/bnx2-*-09-5.0.0.j3.fw /media/XXXX
    • Actually I had also an additional Intel network card so I could have skipped this step...
  • Partitionning:
    there is a first primary partition for Dell Utilities (FAT16), I left it just in case...;
    there is also a second primary partition: 2Gb of FAT32, empty, so I deleted it.
    partition #2: primary 10Gb ext3 / label=ROOT
    partition #3: primary 16Gb swap
    partition #5: logical 2Tb physical volume for LVM
    Configure LVM / ok to write table / Create VG with sda5, called DATA
  • Tasksel: SSH & standard utilities
  • Reboot
• SSH: PermitRootLogin no / ssh-copy-id ...
• Install mc, sudo (adduser xxx sudo)
• Renaming interfaces (always easier to remember what's plugged where...)
  • à la ifrename
    • aptitude install ifrename
    • Create /etc/iftab then reboot

intelG mac 00:1b:21:xx:xx:xx
intelD mac 00:1b:21:xx:xx:xx
bcm1   mac 84:2b:2b:xx:xx:xx
bcm2   mac 84:2b:2b:xx:xx:xx

• • à la udev
    • actually we don't need ifrename because udev is now doing the same, see /etc/udev/rules.d/70-persistent-net.rules, you can simply change the NAME key
  • Be sure the old name is not used anywhere else in your config, typically in /etc/network/interfaces

XEN

• see notes on Debian wiki
• aptitude install linux-image-2.6.32-5-xen-amd64 xen-tools xen-utils
• backup /etc/xen/xend-config.sxp
• edit /etc/xen/xend-config.sxp, and uncomment line "(network-script network-bridge)" or for a non-default interface ethX: "(network-script 'network-bridge netdev=ethX')"
• reboot
• aptitude remove --purge linux-image-2.6.32-5-amd64 linux-image-2.6-amd64
• /etc/default/grub => GRUB_DEFAULT=2
• update-grub
• reboot
• cat /proc/xen/capabilities #(to check xend is running)
• Edit the config file for creating images (/etc/xen-tools/xen-tools.conf) to your needs:

--- xen-tools.conf.orig 2010-05-30 22:42:25.000000000 +0200
+++ xen-tools.conf      2010-08-17 17:47:35.000000000 +0200
@@ -52,7 +52,7 @@
 # LVM volume group here instead
 #
 ##
-# lvm = vg0
+lvm = vg0
 
 
 #
@@ -125,12 +125,12 @@
 #  Disk and Sizing options.
 ##
 #
-size   = 4Gb      # Disk image size.
+size   = 8Gb      # Disk image size.
 memory = 128Mb    # Memory size
 swap   = 128Mb    # Swap size
 # noswap = 1      # Don't use swap at all for the new system.
 fs     = ext3     # use the EXT3 filesystem for the disk image.
-dist   = `xt-guess-suite-and-mirror -s` # Default distribution to install.
+dist   = squeeze  # Default distribution to install.
 image  = sparse   # Specify sparse vs. full disk images.
 
 #
@@ -166,7 +166,7 @@
 #
 # Uncomment this if you wish the images to use DHCP
 #
-# dhcp = 1
+dhcp = 1
 
 
 ##
@@ -254,10 +254,10 @@
 #
 #  You may specify the things to use here:
 #
-# serial_device = hvc0 #default
+serial_device = hvc0 #default
 # serial_device = tty1
 #
-# disk_device = xvda #default
+disk_device = xvda #default
 # disk_device = sda
 #

1. xen-create-image --hostname my-xen1 --dhcp --dir /home/s1-xen1/