Difference between revisions of "Netbook Asus 1005HA"

Revision as of 14:13, 7 July 2010

Characteristics

ASUS 1005HA ACPI BIOS revision 1102
Build Date 10/16/09
EC Firmware Version:EPCD-029
CPU Intel Atom N280 @ 1.66GHz, FSB 667MHz, L1 24kb, L2 512kb (2 logical cores, 1 physical)
2Gb 667MHz DDR2 non-ECC CL5 SODIMM (the original one was a 1Gb SODIMM)
1024x600 Intel Corporation Mobile 945GME Express Integrated Graphics Controller
BIOS v02.58 American Megatrends
HDD ST9250315AS 250GB

Disk /dev/sda: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x8da2c67c

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1       13055   104857600    7  HPFS/NTFS
/dev/sda2           13055       29094   128835584    7  HPFS/NTFS
/dev/sda3           29094       30400    10485760   1b  Hidden W95 FAT32
/dev/sda4           30400       30401       16064+  ef  EFI (FAT-12/16/32)

Atheros AR8132 / L1c Gigabit Ethernet Adapter
Atheros AR9285 Wireless Network Adapter (PCI-Express) AW-NE785H
ASUSTek Broadcom Bluetooth 2.1 (USB) AW-BT253
Battery LION ASUS 1005HA 5800mAh 63Wh
Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller
Webcam 0.3Mpx UVC 1.00 IMC Networks (13d3:5108)
SynPS/2 Synaptics TouchPad

Ubuntu

Install

For this one I wanted a minimal maintenance stuff for basic laptop operations so I chose the latest Ubuntu at the moment: Lucid Lynx.
Actually they have a version special for netbooks, installable from a USB stick, cool:

Ubuntu Netbook 10.04

The only thing is that I wanted to only replace the 2 NTFS partitions and keep the last 2 partitions for now.
First time I tried I used the partition tool from Ubuntu installer but if it succeeded completing the install, after reboot it appeared that the partition table didn't contain refs to the root partition, ouch! So the new partition table was never written to the disk.
I rebooted on a good old FCCU liveCD v12 and changed the partition table the way I wanted then I did again the Ubuntu install, this time without troubles.

I advise to keep at least the EFI partition as it's an 8Mb primary partition used by the BIOS for its "Boot Booster".
In case you already deleted it, simply recreate it with fdisk: 8Mb, type "ef". On reboot, hit F2, and re-enable boot booster in the BIOS.
Mine is at end of the 250Gb HDD:

  Device Boot      Start         End      Blocks   Id  System
/dev/sda4           30400       30401       16064+  ef  EFI (FAT-12/16/32)

Out-of-the-Box

Working:

Suspend-to-RAM
Suspend-to-Disk (hibernate)
Webcam
VGA output
Ethernet
Wi-Fi
Audio playback
CPU freq scaling 1/1.33/1.66GHz, ondemand
sdcard reader
Silverkey disable touchpad
Hotkeys: suspend, Wi-Fi on/off, disable touchpad, brightness up/down, volume off/up/down
Bluetooth, it detected a W300i phone and I could use the phone as remote control OOB, could use it to access Internet as well apparently
My 3G USB key (Vodaphone K3565 = Huawei E160)

Not working?:

multi-touchpad. See below the paragraph about Touchpad
audio mic. See below the paragraph about Microphone
Hotkeys: backlight on/off (not clear, it worked at the beginning, anyway it's barely usable without any backlight... Once Jupiter is used it seems it's used as VGAOFF)
Hotkeys: hotkey display toggle, hotkey display resize, taskmanager, super-hybrid-engine. See below how to use them with eeepc-laptop & Jupiter

Tuning with eeepc-laptop

This modules gives access to the eee hotkeys & eee Super Hybrid Engine for better powersafe control

Install driver

$ modinfo eeepc-laptop
filename:       /lib/modules/2.6.32-23-generic/kernel/drivers/platform/x86/eeepc-laptop.ko
license:        GPL
description:    Eee PC Hotkey Driver
author:         Corentin Chary, Eric Cooper
srcversion:     9A474055673699361160D37
alias:          acpi*:ASUS010:*
depends:        
vermagic:       2.6.32-23-generic SMP mod_unload modversions 586 
parm:           hotplug_disabled:Disable hotplug for wireless device. If your laptop need that, please report to acpi4asus-user@lists.sourceforge.net. (bool)

sudo vi /etc/default/grub
=> GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=Linux"
sudo update-grub
reboot

Now eeepc-laptop kernel module will be properly loaded

In /var/log/syslog

eeepc_laptop: Eee PC Hotkey Driver
eeepc_laptop: wlan hotplug disabled
eeepc_laptop: Hotkey init flags 0x41
eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
eeepc_laptop: TPD (8000000) not reported by BIOS, enabling anyway
eeepc_laptop: Get control methods supported: 0xe101713
eeepc_laptop: Backlight controlled by ACPI video driver
input: Asus EeePC extra buttons as /devices/platform/eeepc/input/input11
NetworkManager: <info>  Found wlan radio killswitch rfkill5 (at /sys/devices/platform/eeepc/rfkill/rfkill5) (driver eeepc)

sysfs controls

$ ls /sys/devices/platform/eeepc/
available_cpufv  cpufv_disabled   input/           subsystem/
camera           disp             modalias         uevent
cardr            driver/          power/           
cpufv            hwmon/           rfkill/

Display:

/sys/devices/platform/eeepc/disp:
1 = LCD
2 = CRT
3 = LCD+CRT

If you run X11, you should use xrandr instead.

Camera:

/sys/devices/platform/eeepc/camera:
1 = on
0 = off

SDCard reader:

/sys/devices/platform/eeepc/cardr:
1 = on
0 = off

CPU clock configuration:

/sys/devices/platform/eeepc/cpufv:
0 = Super Performance Mode
1 = High Performance Mode
2 = Power Saving Mode

Reading this file will show the raw hexadecimal value which is defined as follow:

| 8 bit | 8 bit |
    |       `---- Current mode
    `------------ Availables modes

For example, 0x301 means: mode 1 selected, 3 available modes.

Jupiter

Jupiter is taking care of multiple power saving settings including the eee SHE & GMA950 overclocking if you install also jupiter-support-eee
See http://www.webupd8.org/2010/06/jupiter-take-advantage-of-asus-super.html To install it, there are a few pre-requisite:

aptitude install libnotify-bin acpi

Get .deb packages jupiter & jupiter-support-eee from here & install them

It takes also care of the extra FN buttons (there is also packages eee-applet & eeepc-acpi-scripts or eeepc-control if you prefer not to use Jupiter)

Applet will start at reboot, otherwise you can already start it manually by calling "jupiter.exe" (oups, C#...)
Hovering applet displays CPU temperature.

Issue: very slow at displaying messages when pressing several times / several buttons in a short amount of time.

Support:

Touchpad

aptitude install gpointing-device-settings

& enable circular scrolling (System / Pointing Devices)

For multi-touch I'm not sure how to proceed. Lucid Lynx doesn't use hal anymore.
See

Microphone

Microphone does not work out of the box.
From here:
Install the pulse audio tools

aptitude install paman pavucontrol pavumeter padevchooser

Sound & Video / PulseAudio Volume Control / Input Devices tab:
Unmute audio
Unlock channels
Set front left channel to 100% and the front right channel to 0%.

Additional packages

Skype

Enable Canonical PArtners Repositories: System / Software Sources / Other Software:

http://archive.canonical.com/ubuntu lucid

aptitude install skype

Misc packages

openssh-server
mc
encfs
gstreamer0.10-plugins-ugly gstreamer0.10-ffmpeg

Bugs

At reboot I sometimes encountered the following bug: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/572279

Firmware upgrade

It has v1102, since there were a couple of new versions:

1401 Update brightness table
1301 Improve Wifi performance
1301 Update EC firmware
1203 Fix there is no "safely remove hardware" icon in windows 7 when plug in SD card.

So let's try to install v1401

http://support.asus.com/download/download.aspx
- EEE family / EEE PC / 1005HA / Linux
- BIOS 1401
Unzip archive
Rename file 1005HA-ASUS-1401.ROM into 1005HA.ROM and move it to a USB stick (my 6Gb USB HD wasn't detected I had to use a real 1Gb USB Flash)
Reboot on the USB by pressing ALT-F2 while rebooting
Flash is done automatically
Remove USB stick & reboot

@@ Line 27: / Line 27: @@
 ==Ubuntu==
+===Install===
 For this one I wanted a minimal maintenance stuff for basic laptop operations so I chose the latest Ubuntu at the moment: Lucid Lynx.
 <br>Actually they have a version special for netbooks, installable from a USB stick, cool:
@@ Line 33: / Line 34: @@
 <br>First time I tried I used the partition tool from Ubuntu installer but if it succeeded completing the install, after reboot it appeared that the partition table didn't contain refs to the root partition, ouch! So the new partition table was never written to the disk.
 <br>I rebooted on a good old FCCU liveCD v12 and changed the partition table the way I wanted then I did again the Ubuntu install, this time without troubles.
+I advise to keep at least the EFI partition as it's an 8Mb primary partition used by the BIOS for its "Boot Booster".
+<br>In case you already deleted it, simply recreate it with fdisk: 8Mb, type "ef". On reboot, hit F2, and re-enable boot booster in the BIOS.
+<br>Mine is at end of the 250Gb HDD:
+   Device Boot      Start         End      Blocks   Id  System
+ /dev/sda4           30400       30401       16064+  ef  EFI (FAT-12/16/32)
 ===Out-of-the-Box===
 Working: