View source for Facedancer

==Links==
* http://travisgoodspeed.blogspot.be/2012/07/emulating-usb-devices-with-python.html
* http://travisgoodspeed.blogspot.be/2012/10/emulating-usb-dfu-to-capture-firmware.html
* http://blog.opensecurityresearch.com/2012/11/solder-time-facedancer11-and-goodfet41.html
* http://goodfet.sourceforge.net/hardware/facedancer11/
* http://goodfet.sourceforge.net/tutorial/
==Making==
I met Travis at Troopers2013 and he was very kind of giving me one Facedancer11 PCB.
<br>I soldered the elements by reflow with solder paste in a kitchen pan, on a cooking paper and with good ventilation.
==Installation==
<source lang=bash>
sudo apt-get install python-sqlite python-serial gcc-msp430
svn co https://goodfet.svn.sourceforge.net/svnroot/goodfet
cd goodfet/trunk/client/
sudo make link
cd goodfet/trunk/firmware/
goodfet.bsl --dumpinfo |tee info.txt
</source>
Mine:
<pre>
MSP430 Bootstrap Loader Version: 1.39-goodfet-8
Transmit default password ...
@1000
aa 55 ff 3f cd ab aa 55 34 12 ff ff aa 55 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 20 84 fe 16 ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 08 10 00 80 01 00 11 80 9b 0b c2 0d 2a 80 f5 06 40 08 fe 08 ff ff ff ff ff ff ff ff 01 08 82 8f
8a 8e 7b 8d b3 86 
</pre>
My uC was a msp430f2619 so:
<source lang=bash>
cp lib/msp430f2617.c lib/msp430f2619.c
board=facedancer11 mcu=msp430f2619 make clean reinstall installinfo
</source>

==Usages==
===goodfet.monitor listapps===
 GoodFET with f26f MCU
 Clocked at 0x8f82
 Build Date: 2013-03-28 23:38
 Firmware apps:
 Monitor
 SPI
 MAXUSB

===goodfet.monitor testleds===
 Flashing LEDs
 Flashed 1 LED.
===goodfet.maxusb info===
First connect target USB
 Connected to MAX342x Rev. 4
===goodfet.maxusbftdi===
 goodfet.maxusbftdi
On target:
 cat /dev/ttyUSB0
Or, as sometimes previous command sends only one char at a time:
 screen /dev/ttyUSB0
 [...]
 GoodFET emulates FTDI properly, if you can read this!
 [...]
===goodfet.maxusbmass===
<source lang=bash>
dd if=/dev/zero of=test.img bs=512 count=10000
/sbin/mkfs.vfat test.img 
mkdir test
sudo mount -o loop test.img test
echo hello |sudo tee test/hello.txt
sudo umount test

goodfet.maxusbmass test.img 
</source>
===goodfet.maxusbhid===
On target, chars are typed in an OS-dependent way:
 Python does USB HID on Linux!
===goodfet.maxusbdfu===
Emulating Ubertooth device to capture firmware:
 goodfet.maxusbdfu FFFF 0004
On target:
 ./ubertooth-dfu --write bluetooth_rxtx.dfu
 Checking firmware signature
 ............................................................................................
 Write complete
==Scapy support==
http://rmspeers.com/archives/252
==Raspdancer==
Merging Facedancer & Raspberry Pi
===Why?===
Facedancer11 is a one-purpose version of the flexible GoodFET board.
<br>It was well designed to move all the intelligence into the host controller, not in the embedded uC.
<br>Facedancer11 hardware can be seen as:
  USBconn -- FT232RL -- MSP430F2618TPM -- MAX3420E -- USBconn
where the first two chips are only converting busses:
  USBconn -- FT232RL -- MSP430F2618TPM -- MAX3420E -- USBconn
          USB   <>   UART     <>       SPI   ...   (USB)
BoM view (excluding taxes, Farnell prices):
  USBconn -- FT232RL -- MSP430F2618TPM -- MAX3420E -- USBconn
  USBconn +  5.45€   +  13.03€         +  8.27€    +  USBconn
So 18.48€ to talk SPI over UART over USB while the Raspberry-Pi has natively SPI, hmmm.
<br>Bus speed view: yes there is a kind of bottleneck there...
  USBconn -- FT232RL -- MSP430F2618TPM -- MAX3420E -- USBconn
         12MB/s      115200bauds       26MHz
<br>Let's try to make a RPi extension board with only the MAX3420E.
<br>And to save a few cents and construction pain let's replace the USB connector by a USB cable from a cannibalized mouse.
<br>So:
                         RPI-MODA-256M -- MAX3420E -- USBcable
From a BoM point of view this becomes (depending on what you add to the RPi, nice casing etc):
                         RPI-MODA-256M -- MAX3420E -- USBcable
                         27.66€        +  8.27€
Bus speed view:
                         RPI-MODA-256M -- MAX3420E -- USBcable
                                       26MHz
And we get a fully autonomous facedancer which can be even powered over USB and controlled remotely

===Schematics===
<pre>
MAX Signal RPi Signal
P3  Vcc    P17 3v3   \  0.1uF -- GND
P4  Vcc    P17 3v3   /
P5  GND    P25 GND
P6  GND    P25 GND
P10 -RES   P15 GPIO22
P11 SCLK   P23 SCLK
P12 -SS    P24 CE0
P13 MISO   P21 MISO
P14 MOSI   P19 MOSI
P17 INT    currently not connected, could be e.g. P13=GPIO27
P18 GND    P25 GND
P19 GND    P25 GND ---------- USB conn GND
P20 D-     ----------- R33 -- USB conn D-
P21 D+     ----------- R33 -- USB conn D+
P22 Vcc    P17 3v3  \  1uF -- GND
P23 Vcc    P17 3v3  /
P24 VBCOMP ------------------ USB conn Vcc -- 1uF -- GND
P26 XI     ------------Xtal1- 18pF -- GND
P27 XO     ------------Xtal2- 18pF -- GND
</pre>
===First proto===
[[File:Raspdancer-proto1.jpg|400px]]
[[File:Raspdancer-proto1-full.jpg|400px]]

===Code===
Travis did an amazing job at building a Python library and examples for the MAX3420E, let's reuse them!
<br>You'll need to get [[Raspberry_Pi#GPIO|GPIO Python support]] and [[Raspberry_Pi#SPI|SPI Python support]] for your Raspberry Pi.
<br>From the original facedancer code, you'll need GoodFETMAXUSB.py and the goodfet.maxusb* scripts
<br>Then instead of the original GoodFET.py library, use [{{#file: GoodFET.py}} this GoodFET.py version]:
<source lang=python>
#!/usr/bin/env python
# (C) 2013 Philippe Teuwen <phil at teuwen.org>

import spi
import RPi.GPIO as GPIO

class GoodFET:
    data=""
    def __init__(self, *args, **kargs):
        GPIO.setmode(GPIO.BOARD)
        # pin15=GPIO22 is linked to MAX3420E -Reset
        GPIO.setup(15, GPIO.OUT, initial=GPIO.LOW)
        GPIO.output(15,GPIO.HIGH)
        spi.openSPI(speed=26000000)
    def __del__(self):
        spi.closeSPI()
        GPIO.cleanup()
    def writecmd(self, app, verb, count=0, data=[]):
        if verb: # ignore all but R/W cmd
            return
        if isinstance(data,str):
            data = [ord(x) for x in data]
        data = tuple(data)
        data = spi.transfer(data)
        self.data = "".join([chr(x) for x in data])
    def serInit(self):
        pass
</source>
There are probably better ways to integrate it into the GoodFET software stack but with this small code snippet, you can take the latest great GoodFETMAXUSB.py and goodfet.maxusb* python scripts and just drop them along this GoodFET.py, without need for re-applying any patch.

Note that goodfet.maxusbhid is becoming a bit too quick and I'm missing the beginning of the injected string. I had to add some initial "key up" chars ("\x00" * 20) in typestring() in GoodFETMAXUSB.py:
<source lang=python>
def typestring(self):
    if self.typestrings.has_key(self.OsLastConfigType):
    return ("\x00" * 20) + self.typestrings[self.OsLastConfigType];
else:
    return self.typestrings[-1];
</source>